FMF Supply
EPC-A12SR Servo Edge Web Guide Kit with US-400S Ultrasonic Sensor, 150mm 2KN Actuator
EPC-A12SR Servo Edge Web Guide Kit with US-400S Ultrasonic Sensor, 150mm 2KN Actuator
Couldn't load pickup availability
EPC-A12SR servo edge web guide kit with US-400S ultrasonic sensor
This listing is for an EPC-A12SR controller kit supplied with a US-400S ultrasonic edge sensor and a PD-204L150T servo actuator. In this standard configuration, the set is intended for non-contact edge detection and servo edge correction on non-breathable moving web materials.
The US-400S ultrasonic sensor in this set is not suitable for cloth, woven fabric, mesh, porous web material or breathable material. If your material allows air to pass through it, contact us before ordering so we can help check a different sensor configuration.
The EPC-A12SR controller platform can support more than one guiding mode when it is matched with the required sensor and actuator configuration. Those controller-level capabilities are separate from what is included in this US-400S kit.
What this standard set is for
- Single-edge web guiding / edge position control on non-breathable moving web materials
- Film, foil, label stock, plastic sheet and non-breathable strip material edge alignment
- Printing, packaging, slitting, winding, rewinding and converting lines that need automatic lateral edge correction
Material fit
| Recommended for this US-400S set | Non-breathable film, foil, label stock, plastic sheet and similar non-porous web materials |
| Not suitable for this US-400S set | Cloth, woven fabric, mesh, porous web material and breathable material |
Controller platform capability vs. this kit
| EPC edge guiding | Included with this US-400S ultrasonic edge sensor set for suitable non-breathable materials |
| LPC line guiding | Requires a suitable line, color mark, optical or CCD detection setup |
| CPC center guiding | Requires a matching center or dual-edge sensor arrangement |
| SPC serpentine correction | Depends on the machine layout and matched sensor/control configuration |
Main features of the included set
- EPC-A12SR edge/line position controller used here as an ultrasonic edge guiding controller
- PD-204L150T servo actuator with 150 mm stroke and 2KN / 200 kgf thrust
- US-400S ultrasonic sensor for non-contact web edge detection on suitable non-breathable materials
- Color HMI controller with manual/auto operation and direction controls
- Included power supply accepts 100-240V AC input and outputs 24V DC for the control system
Package contents
| EPC-A12SR correction controller | 1 pc |
| PD-204L150T servo actuator | 1 pc |
| US-400S ultrasonic edge sensor | 1 pc |
| Power supply | 1 pc, 100-240V AC input |
| Connecting cables | 3 pcs |
| Mounting bracket | 1 pc |
Controller specifications
| Model | EPC-A12SR |
| Controller supply voltage | DC 24V-45V, standard 24V |
| Motor drive capacity | 24V-45V, max 10A |
| Analog inputs | 3 channels, 0-5V, 20K ohm impedance |
| Sensor power supply | DC 12V, max 350mA |
| Correction response time | 0.5 ms |
| Analog input resolution | 12-bit ADC |
| Switch inputs | 3-channel NPN |
| Supported sensor categories | Ultrasonic, photoelectric, color mark, CCD, matched according to the guiding task |
| Controller drive speed range | 1-75 mm/s |
| Protection rating | IP53 |
Included US-400S sensor and actuator
| Ultrasonic sensor model | US-400S |
| Sensor use in this set | Non-contact edge detection on suitable non-breathable web materials |
| Sensor supply | DC 12V |
| Sensor output | DC 0-5V |
| Detection range | 8 mm (+/-4 mm) |
| Detection accuracy | 0.1 mm |
| Actuator model | PD-204L150T |
| Actuator thrust | 2KN / 200 kgf |
| Actuator stroke | 150 mm (+/-75 mm) |
| Maximum actuator speed | 40 mm/s |
Ordering notes
- This standard set includes the US-400S ultrasonic edge sensor and PD-204L150T actuator.
- Do not choose this US-400S set for cloth, woven fabric, mesh, porous web material or breathable material.
- It does not include photoelectric, color mark, CCD or dual-edge center-guiding hardware unless separately confirmed.
- For breathable materials, line guiding, color mark tracking, CCD detection, center guiding, serpentine correction setup or a different actuator stroke/thrust, contact us before ordering.
- The plug and voltage are configured according to the customer's shipping country by default.
- For matching support, share the web material, web width, line speed, guiding mode and installation space.
FAQ
What is included in this EPC-A12SR set?
One set includes the EPC-A12SR controller, PD-204L150T servo actuator, US-400S ultrasonic edge sensor, power supply, connecting cables and mounting bracket.
What guiding task is this standard US-400S set for?
It is for ultrasonic edge detection and servo edge correction on suitable non-breathable moving web materials.
Can I use this US-400S set for cloth or breathable material?
No. The US-400S ultrasonic sensor in this set is not suitable for cloth, woven fabric, mesh, porous web material or breathable material.
Can this standard set do line guiding or center guiding?
The EPC-A12SR controller can be configured for those modes, but this standard US-400S set is sold as an ultrasonic edge guiding kit. Line guiding, color mark tracking, CCD detection or center guiding requires the matching sensor setup.
What actuator is included?
The included actuator is PD-204L150T, with 150 mm stroke, 2KN / 200 kgf thrust and 40 mm/s maximum speed.
What sensor is included?
The included sensor is the US-400S ultrasonic edge sensor for non-contact web edge detection on suitable non-breathable materials.
What power input does the set use?
The included power supply accepts 100-240V AC input and outputs 24V DC for the control system.
